Mr-Glass Home Additions & ADU Nationwide

Mr-Glass Home Additions & ADU: The Walnut Creek Owner’s Guide

We stock and install Mr-Glass-compatible glazing systems for home additions and ADU projects in Walnut Creek, with typical installed pricing from $45,000 to $130,000 for full additions and $90,000 to $220,000 for detached ADUs. Most Mr-Glass specification reviews are completed same-day, and we carry common frame profiles and gasket replacements on our trucks. Most Walnut Creek homeowners discover their Mr-Glass system is failing when they notice drafts around a sunroom addition, condensation between panes in an ADU slider, or visible sag in a glass wall that was specified for a lighter load than the Contra Costa wind zone requires.

Call (510) 686-6370

Which Mr-Glass Models This Applies To

Mr-Glass produces several architectural glazing lines relevant to residential additions: the 6000 Series thermally broken storefront, the 4500 Series curtain wall (often specified for modern ADUs with full-height glass), and the 2500 Series terrace door and window line. The part you need depends on which extrusion profile was originally specified. Check the edge of the frame for a stamped series number, or measure the visible frame depth: 6000 Series runs 6 inches, 4500 Series at 4.5 inches, and 2500 Series at 2.5 inches. The glazing gasket part numbers are not cross-compatible between series.

For OEM versus aftermarket, we source Mr-Glass factory gaskets and pressure plates for the 6000 and 4500 Series because the thermal break geometry is proprietary. For the 2500 Series, we use a tested equivalent from a secondary supplier that matches the durometer and UV rating at roughly 30% less cost. We document which route we recommend in the written quote, with the spec sheet attached, before any work starts.

Signs Your Mr-Glass Home Additions & ADU Is Failing

• Condensation between glass panes. The insulated glass unit (IGU) seal has failed, which means the desiccant inside the spacer bar is saturated. In Walnut Creek, we see this accelerate on south-facing additions where daily thermal cycling stresses the edge seal.
• Draft at frame perimeter or operable sash. The compression gasket has taken a permanent set and no longer rebounds against the sash. This is common in Mr-Glass 2500 Series terrace doors after 8-12 years of California sun exposure.
• Visible frame sag or glass panel shift. The structural silicone or pressure plate screws have loosened, or the original specification underestimated dead load. We found this in a Saranap addition where the 4500 Series curtain wall was carrying triple-pane units heavier than the design allowed.
• Water staining at interior sill or adjacent drywall. The weep system is blocked, or the sill pan flashing was omitted during original install. Walnut Creek’s winter wind-driven rain will find any gap in the drainage path.
• Operable hardware binds or won’t latch. The sash has dropped due to hinge wear, or the multipoint lock no longer aligns with the keeper. On Mr-Glass 2500 Series units, the hinge mortise can elongate in the aluminum if the door is oversize for the hardware rating.

Before

After

Replacement Cost & What’s Included

The range depends on three factors: series (6000 Series extrusions cost more per linear foot), glass specification (low-E, laminated, or acoustic interlayer), and access (second-story work or confined ADU sites in Walnut Creek’s older neighborhoods add labor hours). Every quote from Rowan Construction Group is a flat written price with line-item scope. Under Clause 1 of the Haven Standard, that price is delivered before anyone picks up a tool. The 365-Day Done Right Promise covers the installation, and the IGU carries the manufacturer’s warranty against seal failure.

DIY or Call Us?

There is one thing a homeowner can safely check: verify whether the weep holes at the exterior sill are clear of debris. Use a pipe cleaner or compressed air, nothing sharp. Beyond that, Mr-Glass glazing systems involve single- or dual-pane units weighing 80-300 pounds, set in aluminum extrusions with specific torque sequences on pressure plates. Removing a failed IGU without proper suction cups and frame protection risks glass breakage, frame distortion, and personal injury. The 4500 and 6000 Series also use structural silicone that requires controlled cure conditions. We do not recommend DIY replacement on any of these systems.

Call (510) 686-6370 to schedule your free estimate. We’ll identify the series, measure the opening, and give you a written price with the part spec named.

FAQs