Mr-Glass Roofing Nationwide

Mr-Glass Roofing: The Walnut Creek Owner’s Guide

Mr-Glass roofing systems installed in Walnut Creek typically run $8,000-$20,000 for full replacement and $400-$1,800 for targeted repairs, depending on whether we’re matching a single panel section or addressing membrane failure across the assembly. We stock Mr-Glass-compatible glazing gaskets, compression bars, and weep-channel components on our Walnut Creek trucks, and most part replacements are completed in one visit. Most homeowners discover a problem when they spot water staining on the interior ceiling directly below a glass roof section, or when a panel fogs between the laminated layers after a Contra Costa thermal cycle.

Call (510) 686-6370

Which Mr-Glass Models This Applies To

Mr-Glass produces several roofing product lines, and the part you need depends on whether your system is a structural silicone-glazed unit, a captured-gasket system, or their newer thermally broken framing. Check the aluminum extrusion for a stamped series number - typically found on the interior face of the rafter cap - or photograph the end dam detail where the glass meets the wall. The SG-200 series uses a single durometer EPDM gasket that compresses against monolithic glass, while the TG-300 thermal line requires a dual-hardness gasket with an integral thermal separator; swapping one for the other guarantees a leak within the first winter.

We source OEM Mr-Glass gaskets and weep hardware through their regional distributor in San Leandro, though for certain legacy series we specify a comparable aftermarket gasket from Schlegel or Ultrafab when the original tooling has been retired. The aftermarket equivalent must match the original’s Shore A hardness within 5 points and the compression set rating per ASTM D395 - we document both specs on the written quote. If your system dates to the 2008-2014 production run, there’s a known compatibility issue with the original polycarbonate weep channels, which crystallized in direct California sun; we replace these with UV-stabilized nylon versions that have held up through eight years of Walnut Creek exposure on our tracking records.

Signs Your Mr-Glass Roofing Is Failing

• Interior water staining that follows the rafter lines. This pattern indicates gasket compression failure at the glass-to-frame interface, not a breached panel. The EPDM has taken a permanent set and no longer seals against thermal expansion movement.
• Fogging or condensation between laminated glass layers. The edge delamination has breached the inner seal of the insulated glass unit. This cannot be repaired in place; the panel requires removal and reglazing with a new IGU.
• Visible gasket extrusion or “smiling” at panel corners. The gasket has shrunk beyond its design compression range, usually from age plus Contra Costa’s 40-degree daily temperature swings in summer. Water enters at the relaxed corner first.
• Weep channel blockage with standing water visible at the sill. Pollen, leaf debris, and hard water deposits clog the narrow weep slots. On Mr-Glass systems the weep path is internal to the sill extrusion; clearing it requires partial disassembly.
• Aluminum frame chalking with white residue at horizontal surfaces. The anodized coating has degraded past its 20-year design life. This is cosmetic until the substrate pits, but pitting accelerates once it starts in Walnut Creek’s occasional salt-air influence from the delta.

Before

After

Replacement Cost & What’s Included

For Mr-Glass part replacement in Walnut Creek, expect $400-$1,800 for most gasket, weep, and minor frame repairs, and $8,000-$20,000 if the glass units themselves have failed and require full reglazing. The lower end covers gasket replacement on a four-panel bay window roof with OEM-spec material and resealing; the upper end reflects a full thermal-unit swap on a larger skylight assembly with crane access.

Our written quote itemizes: parts by manufacturer and part number, labor hours at our published rate, sealant specification (we use Dow 795 on Mr-Glass systems for its movement capability), and disposal. Under Clause 1 of the Haven Standard, that written price is the price - no change proceeds without a signed change order, which is the discipline that has kept our projects within a few percent of the agreed cost across 4,000-plus jobs. The 365-Day Done Right Promise covers the installation; gasket material carries the manufacturer’s prorated warranty against defects.

DIY or Call Us?

A homeowner can safely inspect from the interior: photograph the series stamp, check weep outlets for visible blockage, and note any interior staining pattern. Do not attempt gasket replacement or panel removal yourself. Mr-Glass panels are heavy - typically 6-8 pounds per square foot for laminated insulated units - and the gasket must be compressed uniformly with a specialized roller tool to achieve the design seal pressure. An uneven gasket seat leaks immediately and may void any remaining glass warranty. The aluminum frame edges are also sharp enough to require cut-resistant gloves.

We’ve responded to three Walnut Creek calls in the past year where a homeowner’s self-installed gasket leaked worse than the original failure. Each time the fix cost more than our initial quote would have, because we had to remove the homeowner’s material and clean the adhesive residue before proper installation. Call (510) 686-6370 and we’ll schedule a free estimate with a written price before any work starts.

FAQs